Racing Parts for Sale

All the parts displayed below are used unless specified in the description.

Feel free to call or text any offer. Everything is negotiable.

If you have any questions please call (cell) 262-510-6246 or (office) 262-446-9747

Email to: kevin@hogantechnologies.com

We accept cash, Visa, Mastercard, or check. (Sorry, no PayPal)

If paying by personal check, we will need to wait for check to clear the bank before shipping items.

Prices indicated do not include shipping.

Wild Incorporated 4130 4-link chassis

This is a 2013 Wild Incorporated 4-link 4130 chassis.

It’s brand new with brake lines, cockpit and most of the deck, and brake pedals.

We can finish it to any stage of completion you want.

$4500

PPM Aluminum Panhard Bar

I have a PPM aluminum panhard bar that is 18 ¾” at it’s shortest length.

Would like to get $75 for it.

Angled four barrel carb spacers for a dirt late model or modified

I have two angled spacers for a dirt late model of dirt modified. This helps keep the bowls level to prevent fuel starvation when the car is rocked up.

(2) are 1 ½” tall at their middle rear point.

The bores are 1 ¾”.

New, they retail for $200 a piece. I’d like to get $100 for each.

Joe’s Bearing Upper Control Arms 8” & 11”

Joe’s bearing upper control arms with steel slotted shafts. One is 8” and the other is 11”.

Both have angled ball joints.

These are brand new in the package.

I need to get $139 each for them.

Allstar 1:1 (2) groove v-belt Pulley System

I have an All star 1:1 (2) groove v-belt pulley system that has never been run.

Part numbers are: All31084 and All31805.

They both measure 6 ?” in diameter.

Top pulley has a ?” pilot for water pump.

I’d like to get $80 for the pair. I really don’t want to separate the two.

Falcon Bell Housings

I have two Falcon bell housings.

These are bare without the starter idler gear.

I would like to get $100 each and sell them as a pair.

I have the coupler mechanism with the drive hub, splined shaft, and the coupler.

$90 for the unit with the HTD pump drive and $70 without the pump drive.

I have additional flywheels, couplers and starters for sale also.

Call, Text or Email with any questions to:

262-510-6246 (Text messaging is preferred) or 262-446-9747

Email to kevin@hogantechnologies.com

(2) Longacre high oil temp sending units

I have two high oil temp sending units.

These will activate a ground when the oil reaches 270 degrees.

They will screw into any ½” NPT port.

I would like to get $15 each. These normally retail for $20. They are new and in the package.

Coleman Reduction 2 Groove V-belt Pulley Set

Three Coleman Pulleys. The (1) bottom pulley is 5 ?” diameter and the (2) top reduction pulleys are 7” in diameter. Coleman part numbers are DS-364 and DS-365.

The top pulleys have a ?” bore to fit the water pump snout. Paired together, they offer a 15% in water pump speed to prevent cavitation and help cooling.

All three together I’d like to get $100. If you only want the matched set of two, I’d  like to get $65.

Manley Pro Series 6.125 rods

I have a set of eight connecting rods. I believe they are Manley Pro Series rods. They 6.125” long, 2.1 main journal, and a .92 wrist pin bore.

I looked them up on line and they go for $1,500 new. I’m looking to get $500.

16 Volt Batteries

          

I have two used sixteen volt batteries.

These are freshly charged and ready to ship.

One is an original Turbo Start and the other is Rock (distributed by Port City Racing)

$100 each.

MSD Chip Set 7000 RPM to 7800 RPM

MSD chip set that ranges from 7000 rpm to 7800 rpm in 200 rpm increments.

These are new in the package.

Would like to get $20 for it.

Crower Solid High-Seat Roller Lifters

Full set of high-seat offset Crower solid roller lifters.

.842 diameter, .750 roller bearing.

They came out of a chevy motor.

They go for around $1,000 new, I’d like to see $500 out of them.

Wehrs Aluminum Bearing Brake Floater for Left Rear

I have a Wehrs aluminum bearing brake floater for left rear.

It was only used a couple of times. It looks like brad new.

Regularly it goes for $190, I would like to get $100 for it.

Falcon Aluminum Transmission

I have a used aluminum Falcon Transmission.

Fairly fresh and in excellent condition.

Used as our spare for years.

Would like to get $800 for it.

Allstar 1:1 (2) groove v-belt Pulley System

All star 1:1 (2) groove v-belt pulley system that has never been run.

Part numbers are: All31084 and All31805.

They both measure 6 ?” in diameter.

Top pulley has a ?” pilot for water pump.

I’d like to get $80 for the pair. I really don’t want to separate the two.

(2) Cast Iron Power Steering Pumps w/ 6” V-belt Pulleys

I have (2) cast iron power steering pumps w/ 6” v-belt pulleys.

Normal retail for these is around $140. I’d like to get $75 for each one or $140 for the pair.

Sweet Steering 305-80831 Aluminum Power Steering Pump

Sweet Steering 305-80831 Aluminum Power Steering Pump with a 6” v belt pulley.
It’s engraved with a 2-15, which I’m assuming is the rebuild date.

Normal retail is between $230 and $250. I’d like to get $140 for it.

This a special 1,700 psi high output pump for for fast dirt style steering systems.

Strange 9″ Ford Aluminum Center Section

A Strange Aluminum Ford 9″ center section with 6.0 gear ratio, and light weight spool.

It only has a couple of nights on it since a rebuild. I believe the spool and bearings were new with the freshen up.

No Yolk.

Asking $700.

 

Call, Text or Email with any questions to:

262-510-6246 (Text messaging is preferred) or 262-446-9747

Email to kevin@hogantechnologies.com

Howe Ball Joints and Parts

Complete Ball Joints

(1) #22412 Used Chrysler Screw in Lower Moog #K727        $35 each

(1) #22300 Used Standard Bolt in Chevy Upper Moog #6024     $35 each

(2) #22301 Used 73-95 GM Truck Upper Moog #K6136     $35 each

(1) #22414 New Chevelle Lower to Pinto Spindle Aluminum Cap     $60

(1) #22414S New Chevelle Lower to Pinto Spindle Steel Cap     $70

Ball Joint Replacement Stems

(4) #22445 +.5 taller Chrysler Screw in Lower Pins. Fits Howe #22412.     $15 each

(1) #22440 Standard Chrysler Length Screw in Lower Pin. Fits Howe #22412.     $15

(1) #22460 71-95 1/2 ton Chevy Truck Lower Press in Ball  Joint Pin. Fits Howe #22419.     $15

(5) #22350 73-95 GM Truck Upper Pin. Fits Howe #22301.     $15 each

(1) #2244105 -.5 length for Chrysler Screw in Lower Pin. Fits Howe #22412.     $15

(1) #223375 +.75 longer for Chevy Upper Ball Joint Pin. Fits Howe #22320.     $15

(4) #22330 Standard Length Chevy Upper Ball Joint Pin. Fits Howe #22320.     $15 each

(2) #223310 +1″ longer for Chevy Upper Ball Joint Pin. Fits Howe #22320.     $15 each

(1) #22434 +.4 Longer Chevy Lower Pin. Fits Howe #22413.     $15

(2) #22430 Standard Chevy Lower Pin. Fits Howe #22430.     $15 each

(4) #22330 Standard Chevy Upper Pin. Fits Howe #22320 & #22300.     $15 each

Ball Joint Repair Parts

(3) #22467 Complete Housings (no pins) to Fit Chrysler Lower with Pinto Spindle.     $25 each

(6) #22415 Aluminum Lower Ball Joint Caps.     $10 each

(5) #22321S Steel Upper Ball Joint Caps.     $10 each

(1) #22321 Aluminum Upper Ball Joint Cap.     $10

(1) #22415S Steel Lower Ball Joint Cap.     $10

 

 

Ford 9″ Aluminum Ratchet Differential

This is a Ford 9″ Aluminum Ratcheting Differential.

Not sure of age. No markings for manufacturer, but it looks like it might be Winters.

$382.

Wilwood Scalloped .810 Rotors

A set of four scalloped .810 rotors; 11.75″ diameter; 8 bolt on a 7″ bolt circle.

Lots of life left in them.

$125 takes all four.

Winters 8″ 4.11 Polished and EDM Cut Ring and Pinion

We have a brand new polished and EDM cut 8″ 4.11 ring and pinion for a quick change.

We bought it and never installed it.

If you would like the entire center section set up we can work out a price complete.

This is perfect for crate motor or spec. motor lower horsepower racing.

It is not recommended for high horse power open motor late models.

We can set everything up with either a spool or a billet differential.

New retail pricing on this is $500.

 

30″ Dash 4 Braided Brake Lines

I have seven 30″ -4 brake lines.

$10 each

Napa Lower Control Arm Bushings

These are supposed to fit 71-72 CHEVROLET CAMAROS AND 70-73 PONTIAC FIREBIRDS.

Part number #267-3258.

$20 each.

 

9″ Ford Steel Ratchet Differential

This is a 9″ Ford Steel Ratcheting Differential.

It might be a Coleman.

$315

Winters Billet Aluminum Quick Change Locker #5114-01

This is a brand new Winters Billet Aluminum Locker for a quick change rear end.

Part #5114-01.

We bought it and never got it installed.

Retails for between $680 and $690.

Would like to get $670 for it.

Winters Sprint Center Section Shortened for “8 R&P

We have a complete Winters sprint center section.

This is the shortened version to accommodate a 8″ ring & pinion.

All the pieces are there, it just needs to be set up.

If you would like to purchase an entire package with the ring & pinion and the spool or differential, I can set it up for you for an additional fee.

Need to get $500.

Napa Stock Upper Ball Joints

(2) NAPA brand upper ball joints; part number 260-1042.

It interchanges with MOOG K772.

$15 each

Speedway Motors Pitman Arms

I have (2) Speedway Motors pitman arms part number 910-32560.

1.12 x 32 spline bore will fit the sweet steering gear boxes.

5″ from center to center on the bores.

Regularly $60, will take $50.

Winters Quick Change Aluminum Spool

I have a used Winters quick change aluminum spool.

Good condition; took it out to put a locker in and never reinstalled.

Need to get $130 for it.

 

‘New’ Chevelle Lower Control Arm

This is a Chevelle lower control arm; new.

It has the round bushing openings.

$99

 

Metric Inner Tie Rod Ends

I have four metric tie rod ends.

(2) have the grease zirk on the side and (2) have the grease zirk on the end.

All four have left hand thread.

$14 each

Mono Ball Lower Control Arm Bushings

These are round mono ball Chevelle lower control arm bushings.

$60 a pair.

US Brake Caliper

We have a brand new US Brake Caliper for a metric left side.

Part #7241-9002 and is an oversize 2 3/4″ piston.

I’ll include a bunch of rebuild o-rings for it free.

Retails on Speedway for $80, we’ll take $50.

Call, Text or Email with any questions to:

262-510-6246 (Text messaging is preferred) or 262-446-9747

Email to kevin@hogantechnologies.com

Bearings and Seals

Bearings

(5) #LM12749 Pinto Bearings #LM12710  $8 each

(3) #L68149 Pinto Bearings #L68110 Race   $8 each

(3) #L67048 Bearings #LMG7010 Race   $6 each

(1) #LM12748 Bearing #LM12710   $9

(3) #LM11949 Bearing #LM11910   $5 each

(1) #M12649 Bearing #M12610   $7

Seals

(2) Federal #9150S      $6 each

(2) Federal #6815      $6 each

(2) Federal #8835s      $6 each

(1) Napa #19753     $6

(2) # A26554     $6 each

(1) # 472572     $6

$100 takes them all

Woodward Steering Rack Parts

Rack Shafts

(3) 18 1/4″ rack shafts with standard tie rod mounting  $50 each

(1) 19 1/4″ rack shaft for clevis end racks (Rocket Length)   $50

(1) 19 3/4″ rack shaft for clevis end racks   $50

 

Pinions

(1) 16 tooth pinion      $50

(1) 17 tooth pinion with the mounting caps     $80

Rack Housings

(1) has a part # of 12202E     $75

(1) has a part # of 9407AC    $75

Misc. Parts

(2) Slave cylinder shafts    $20 each

(2) Slave cylinder hoses    $15 each

(5) Torsion Bars     $18 each

(4) Clevis Rack Ends     $20 each

(5) Slave cylinder mounts     $10 each

(1) Slave cylinder     $50

(1) Rack boot     $10

Will get rid of everything for $500

GM 605 Steering Gear

This is for a used GM 605 Steering gear.

Comes with the pitman arm and one of the fittings.

$50

Steering Wheel Center Pad

(1) Kirkey steering wheel center pad.

$10

Winters Gundrilled Axles

We have one pair of Winters Gundrilled axles.

One is 28″, the other is 32″.

They were purchased for a 58 1/2″ Ford 9″ housing and have never been run.

$250 takes them both.

30″ Dash 4 Braided Brake Lines

I have seven 30″ -4 brake lines.

$10 each

Power Steering Pump Mounts

Power Steering Pump Mounts

 

$30 each

Pinto Spindles

(2) Used Pinto Spindles

$50 each

Ford 9″ Inner Axle Tube Seals

New Ford 9″ inner axle tube seals.

These will fit a 3″ x 3/16″ wall tube.

Need to get $80 for the pair.

 

Napa Stock Upper Ball Joints

(2) NAPA brand upper ball joints; part number 260-1042.

It interchanges with MOOG K772.

$15 each

360 Degree Neck Collars

(2) 360 degree neck collars.

$20 each

58 1/2″ Ford 9″ Rear End

I have a new Ford 9″ rear end housing.

This is a fabricated 58 1/2″ centered housing by HRP.

Spindle snouts for Wilwood 5x5 hubs.

We had it in a car and changed it out for a quick change before delivery.

$400 takes it as you see it.

I do have inner axle seals for it, but those are an additional $80.

Gundrilled axles to fit it are an additional $250.

 

Steel PPM Combo Bearing Birdcages

This is a pair of steel combo PPM bearing birdcages.

$300 for the pair.

Metric Inner Tie Rod Ends

 

I have four metric tie rod ends.

(2) have the grease zirk on the side and (2) have the grease zirk on the end.

All four have left hand thread.

$14 each